ACV 42a-1292-003-0 Модул за управление от волана SWC за Suzuki Ignis/Jimny/Swift/SX4/Vitara 20Pin USB/AUX

Упътване

Упътване на опционален кабелен преход 42arc100

analog

connector: 20 Pin Suzuki

connector: OEM AUX > 3,5 mm Jack

connector: OEM USB > USB-A

check dip switches for retrofit HU

diagnostic LED:

blue constant > Interface active +12V ignition power supply present

red > steering wheel remote control button function recognised

Съвместими модели:

Suzuki Ertiga 2012 - 2015

Suzuki Grand Vitara (JT) 01/2013 - 08/2015

Suzuki Ignis (MF) 01/2017 - 04/2021

Suzuki Ignis (MF) 04/2021 - 08/2024

Suzuki Jimny (GJ) 10/2018 - 09/2020

Suzuki Jimny NFZ (GJ) 04/2021 - 08/2024

Suzuki Swift (FZ/NZ) 09/2010 - 10/2013

Suzuki Swift (FZ/NZ) 10/2013 - 04/2017

Suzuki Swift (AZ) 04/2017 - 03/2024

Suzuki SX4 S-Cross (JY) 10/2013 - 10/2016

Suzuki Vitara (LY) 04/2015 - 08/2018

Following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in functions.

SWC

HU application:

Multilead different HU > item:: 42arc100

General installation instructions:

Verification:

1: Check all operating functions and vehicle setting functions of the OEM HU.

2: Disconnect the OEM HU voltage-free.

3: Check all interface connections for correctness voltage-free.

Connection and connection sequence:

1: Check settings and hardware configuration of the interface voltage-free.

2: Check configuration of the HU connection cable voltage-free.

3: Connect the HU connection cable according to the operating instructions of the retrofit HU.

4: Connect all other connections according to the operating instructions of the retrofit HU.

5: Connect the entire installation to the vehicle with the main connection last.

6: Software configuration of the interface according to the instructions in the item text and in the manual.

7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.

8: Function test of steering wheel remote control and vehicle

Changes to the configuration of the interface and the HU connection cable:

1: Change configuration voltage-free

2: Reconnection see above 5 to 8

In case of malfunction of the interface or the vehicle:

1: Reinstall the OEM HU

2: Operate the OEM HU

3: Establish CAN bus shut down

4: Check the hardware configuration of the interface

5: Reconnection after CAN Bus shut down see above 5 and 6

More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.

More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

1: Connections and changes are to be carried out exclusively by trained specialist installer.

2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.

3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection.

4: Connections and modifications are made on the user's own responsibility without guarantee of function.

5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.

6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.