ACV 42a-1300-001-0 Модул за управление от волана за Toyota 10Pin/6Pin/20Pin analog

Note:

analog

connector: 10 Pin / 6 Pin / 20 Pin Toyota

vehicles with Matsushita / Fujitsu Ten OEM HU

vehicles without JBL / JBL Synthesis / Mark Levinson OEM amplified system

vehicles with 18 Pin CN 700 LAN connector:

steering wheel remote control on the 8 Pin CN 800 connector check before connecting it to the OEM device by measuring

Pin 6: SWC GND

Pin 7: SWC 1

Pin 8: SWC 2

diagnostic LED:

blue constant > Interface active +12V ignition power supply present

red > steering wheel remote control button function recognised

Vehicle application:

Lexus

Lexus IS (XE1) 10/2001 - 11/2005

Lexus IS (XE2) 12/2005 - 11/2008

Lexus IS Cabriolet (XE2) 07/2009 - 11/2010

Lexus IS (XE2) 11/2008 - 11/2010

Lexus IS Cabriolet (XE2) 11/2010 - 10/2013

Toyota

Toyota 4Runner 2002 - 2009

Toyota Auris (E150) 07/2007 - 03/2010

Toyota Avanza 2003 - 2011

Toyota Avensis (T25) 01/2003 - 06/2006

Toyota Avensis (T25) 06/ 2006 - 01/2009

Toyota Avensis (T27) 01/2009 - 12/2011

Toyota Camry 2007 - 2011

Toyota Celica (T23) 10/1999 - 01/2006

Toyota Corolla (E120) 01/2002 - 07/2004

Toyota Corolla (E120) 07/2004 - 02/2007

Toyota Corolla Verso (R1) 05/2004 - 06/2007

Toyota Corolla Verso (R1) 07/2007 - 04/2009

Toyota Estima 2006 - 2016

Toyota FJ Cruiser 2001 - 2007

Toyota Hiace (H1) 11/2006 - 10/2010

Toyota Hilux (N25) 10/2005 - 11/2008

Toyota Hilux (N25) 11/2008 - 12/2011

Toyota Innova 2006 - 2015

Toyota Landcruiser (J12) 01/2003 - 01/2009

Toyota Matrix 2003 - 2014

Toyota MR2 (W3) 04/2000 - 03/2003

Toyota Prado 2003 - 2009

Toyota Previa 2006 - 2019

Toyota Prius ZVW30/ZVW35 (XW3) 06/2009 - 04/2012

Toyota RAV4 (XA2) 10/2000 - 12/2003

Toyota RAV4 (XA2) 12/2003 - 01/2006

Toyota RAV4 (XA3) 03/2006 - 04/2009

Toyota RAV4 (XA3) 04/2009 - 05/2010

Toyota Yaris (XP9) 01/2006 - 01/2009

Toyota Yaris (XP9) 01/2009 - 10/2011

Toyota Vios 2003 - 2007

SWC

HU application:

Multilead different HU > item: 42arc100

General installation instructions:

Verification:

1: Check all operating functions and vehicle setting functions of the OEM HU.

2: Disconnect the OEM HU voltage-free.

3: Check all interface connections for correctness voltage-free.

Connection and connection sequence:

1: Check settings and hardware configuration of the interface voltage-free.

2: Check configuration of the HU connection cable voltage-free.

3: Connect the HU connection cable according to the operating instructions of the retrofit HU.

4: Connect all other connections according to the operating instructions of the retrofit HU.

5: Connect the entire installation to the vehicle with the main connection last.

6: Software configuration of the interface according to the instructions in the item text and in the manual.

7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.

8: Function test of steering wheel remote control and vehicle

Changes to the configuration of the interface and the HU connection cable:

1: Change configuration voltage-free

2: Reconnection see above 5 to 8

In case of malfunction of the interface or the vehicle:

1: Reinstall the OEM HU

2: Operate the OEM HU

3: Establish CAN bus shut down

4: Check the hardware configuration of the interface

5: Reconnection after CAN Bus shut down see above 5 and 6

More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.

More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

1: Connections and changes are to be carried out exclusively by trained specialist installer.

2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.

3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle·s cable assignment diagram before connection.

4: Connections and modifications are made on the user·s own responsibility without guarantee of function.

5: Connections and modifications are made on the user·s own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.

6: Modifications to the pre-assembled wiring harness may invalidate the product·s warranty.